A garage door is usually the heaviest moving object in a house, and the opener's safety features are what keep it from trapping anyone. This ten-minute check uses only what any owner can do safely.
Most garage door openers sold for homes have two protections built in. Federal rules at 16 CFR part 1211 require a residential opener to have inherent primary entrapment protection, and a vertical door must reverse within 2 seconds of touching an obstruction. A secondary device, such as an external photoelectric sensor, an edge sensor or an inherent door sensor, must also be supplied with the opener or as an accessory. When the photoelectric sensor is triggered during closing, the door must reverse and fully reopen. Those protections only help if they still work. Testing them takes a few minutes once a month, and it is worth doing after any power outage, remote reprogramming or work done on the door.
Before you start
Look at the whole door first. Raise it and lower it once with the wall button and listen. Grinding, popping, a door that hangs crooked, frayed cable strands or a gap at the bottom corners are signs to stop testing and call a local garage door company. A door in that condition should not be run through further cycles. If you ever suspect a broken spring, our guide on why to stop and call about a broken spring explains what to do and what not to do.
Clear the area. Keep children and pets out of the garage during the test, and keep cars out of the door's path. The wall button should be the only control in use, and the remote should stay in your hand, not on a visor or a dash where a child can reach it. The Consumer Product Safety Commission says to keep the remote away from children.
Step 1: The photo-eye check
The two small sensors near the floor on either side of the door send a beam across the opening. With the door fully open, wave a broom handle through the beam at ankle height while the door is closing. The door should stop and reverse right away. Never use your body to test this.
If the door ignores the beam, look at both sensors. Wipe each lens with a soft cloth, since dust, cobwebs and sun glare in the hot months can interfere. Check that each sensor is pointed at the other and has not been bumped. Most sensors have a small light that shows when they are aligned. A flickering or dark light points to an alignment or wiring issue. Our guide to a door that won't close covers sensor causes in more detail, and the sensor repair page explains what a visit usually involves.
Step 2: The 2x4 reversal test
The CPSC advises placing a 2x4 flat on the garage floor in the path of the door. Close the door with the wall button. When the door touches the board, it should reverse. If it does not reverse properly, the CPSC says the opener should be disengaged until it is adjusted, repaired or replaced.
Two practical points. Lay the board flat, not on its edge, so the door meets it gently. And do not stand under the door while it runs. If the door fails the test, stop using the opener, close and lock the door if you can, and call someone to look at it. Adjusting travel and force settings is not a step to guess at. Settings that make the test pass by making the door stop short can leave a gap, and settings that are too forceful can defeat the very protection you are testing. The opener repair page describes what a technician looks at.
Step 3: Auto-reverse by the wall button
With the door open, press the wall button to close it, and press it again partway down. The door should stop. Press once more and it should travel up or down depending on the model. If it does not respond to the button at all, check the wall unit's lock switch, a small slider that disables remotes in some models. Make sure it is not set to lock. A stuck wall button can also be a wiring or power issue, and that is a job for a technician.
Step 4: Check the remotes and keypad
Test every remote you own, plus any wall keypad. Weak signals and dead batteries are common, and Austin's hot garages are hard on small batteries. Replace batteries in remotes and in the keypad before assuming the opener is bad. If a remote has gone missing, a lost remote is worth reprogramming against, since anyone who finds it can open your door. The remote and keypad page covers what that usually involves.
Step 5: Know your manual release, and use it with care
Every opener has a manual release, usually a red cord with a handle on the trolley near the door. DASMA's opener guide says to begin with the door closed and use the manual disconnect to detach the door from the opener. It also warns that once the operator is disengaged, the door may unexpectedly begin to open, and that if a spring is broken the door should not be operated until the spring is replaced.
That means two rules. Pull the release only with the door closed, and only if you believe the springs are intact. A door that feels extremely heavy, one with a visible gap in a torsion spring, or one with a loose cable should be left alone. Practice once while the door is down and you are standing safely to the side, so you know how it works before a storm or outage forces the issue. Our power outage and manual release guide goes deeper.
What not to do
Do not adjust springs, cables or the brackets at the bottom corners. Those carry tension, and DASMA says spring systems are dangerous and should be repaired only by trained professionals. Do not wedge a board or a jack under the door to hold it open and then walk away. Do not bypass a sensor with tape or by pointing it away. If a sensor has been tampered with and the door still closes, the protection is gone.
How often, and what to write down
A monthly check is a good habit. Many owners tie it to something else, such as the first of the month or the day the trash goes out. Keep a note on your phone with the date and what you did. If a test starts to fail, you will know roughly when it began. A door that fails once and passes the next time is not safe to assume fixed. Intermittent failures usually trace back to something loose, dirty or worn.
A yearly visit from a local company can cover what you cannot, such as spring tension, cable wear and roller condition. The tune-up page explains the scope. In one national guide, a tune-up costs about $100 to $125, and opener repair runs $75 to $300 in HomeGuide's repair cost guide. Those are national figures, and companies set their own prices.
If the opener is old
Openers made before the current federal entrapment rules may lack a secondary sensor altogether. If yours has no photo-eyes, or has them but fails the reversal test after adjustment, replacement is usually the safer route. The opener installation page and our repair-or-replace guide can help you judge.
If your door failed any step above, tell the company on the phone which one. The number on this page connects you with an independent local garage door company serving Austin and nearby towns.
Frequently asked questions
How often should I test my garage door opener's safety features?
What is the 2x4 test?
The door passed once and failed once. Is it fine?
Can I pull the emergency release if a spring looks broken?
Sources
Last updated: