A door that goes down a few inches and then reverses, or one that never starts, is usually trying to protect you. This guide walks through the safe owner checks first, then the problems that need a professional.
Why a door refuses to close
Most doors that will not close are not broken. They are doing what federal rules require. Under 16 CFR part 1211, a residential garage door opener must have entrapment protection, and an external photoelectric sensor is the usual secondary device. When that sensor is triggered while the door is closing, the door must reverse and fully reopen. So a dirty lens, a bumped bracket or a stray beam of sunlight can keep a perfectly good door open.
This site is a free referral service, not a garage door company. If the checks below do not solve it, call the number on a page here to be connected with an independent local garage door company.
Start with what the door does
Watching the door tells you where to look. The pattern usually falls into one of these groups.
- The door starts down, then reverses and goes back up. Suspect the sensors or an obstruction, or a force or travel setting on the opener.
- The door does not move, but the opener light comes on or you hear a click. Check the remote, the wall control and the lock switch.
- The opener runs and the door does not move, or it hums and strains. This can point to a spring problem, which is not an owner repair.
- The door closes most of the way and stops or stays slightly open. Think travel limits, a binding track or something in the door's path.
- The door closes, but only when you hold the wall button. That often means the sensors are not talking to the opener.
Check the safety sensors
Two small sensors sit on either side of the door opening, usually about six inches off the floor. One sends an invisible beam and the other receives it. Each has a small indicator light, and when they are aligned and clear, both lights are steady. If one is dark or flickering, the beam is blocked or the sensors are out of line.
- Wipe each lens with a soft, dry cloth. Spider webs, dust and Central Texas limestone grit are common culprits.
- Look for anything in the beam: a bag, a tool, a pet bowl, a stack of boxes.
- Check that each sensor is still pointing straight across at the other. A bumped bracket, a lawn mower or a bicycle handlebar can knock one out of line.
- Make sure the wire to each sensor is not loose or chewed.
Hot afternoon sun shining directly into the receiving lens can also confuse a sensor, especially in a west-facing garage during the Austin summer. If the door only fails at certain times of day, that may be why. Shading the lens or moving the sensor is something a company can advise on. If the lights do not return to steady after cleaning and adjusting, call. A failed sensor needs replacing, and the garage door sensor repair page explains what that call looks like.
Check the remote, keypad and wall button
Replace the remote battery first. If the wall button works and the remote does not, the problem is probably the remote or its signal. Look at the wall control as well: many have a lock button that stops remotes and keypads from working, and it is easy to press by accident. If the lock light is on, turn the lock off. If the wall button does nothing and the opener has no light, check that the opener is plugged in and that the outlet has power. The garage door remote and keypad repair page covers programming and replacement.
Obstructions and the reversal test
If the sensors are clean and lit, look at the floor and the door's path. Debris under the bottom seal, a bit of ice-melt crust, or a loose weatherstrip can trip the opener's obstruction detection. A door that reverses when it touches nothing may have its force setting too sensitive or its travel limit set too short, and that is an opener setting best left to a company or the owner's manual.
The reverse behavior matters, and you should not disable it. CPSC advises placing a 2x4 on the floor in the door's path. If the door does not reverse when it touches the board, disconnect the opener until it is adjusted, repaired or replaced. The monthly safety test shows how to run the check correctly. Never tape over a sensor, bridge its wires or hold the button down as a regular workaround. The door is meant to reverse.
Limits, force and the opener itself
Every opener has travel limits that tell it where up and down are, plus force settings that tell it how hard to push. When these drift, a door may stop short of the floor or reverse when it touches the ground. Temperature swings can change how tight a door runs, and Austin's heat and the occasional winter freeze are enough to shift things on an older door. If you suspect the limits are off, the opener's manual covers the adjustment screws or buttons. If you are not comfortable with that, a company can do it as part of an opener visit. See garage door opener repair or garage door tune-up.
Brand matters less than the symptoms. If you have a LiftMaster or Genie, the same steps apply; the LiftMaster opener repair and Genie opener repair pages describe common issues for those units. This site has no affiliation with either brand.
Signs the problem is the door, not the opener
If the door looks crooked, sags on one side, makes a grinding noise, or has a cable hanging loose, stop. A door that has come off its track, a broken cable or a failed spring will not close properly, and forcing it can cause an injury. DASMA says spring systems are dangerous and should be repaired only by trained professionals. Read why to stop and call with a broken spring and the off-track garage door repair page.
What repairs tend to cost
These are national figures, not an Austin price list. HomeGuide lists sensor repair around $85 to $100, with another source at $110 to $200. Opener repair is listed at about $75 to $300, and off-track repair at $170 to $290. A new opener runs $300 to $500. A reasonable company should tell you the likely cause before you agree to anything, and a simple alignment or cleaning is not usually a big bill. The repair cost guide has more on what drives quotes in Austin.
What to tell the company on the phone
A few details make the call faster. Say what the door does when you press the button, whether the sensor lights are steady, whether the opener makes noise, and how old the opener and door are. Mention that you cleaned the lenses and replaced the battery if you did. Ask about after-hours calls, since many companies take them, and ask how they are quoting: parts listed, business name and address, and the manufacturer's warranty on any parts. The hiring guide has a full list of questions.
If you are comparing options in a nearby town, the service areas page lists every town covered, from Round Rock and Cedar Park to Dripping Springs and Lockhart.
Frequently asked questions
Why does my garage door go down and then back up?
Can I bypass the sensors so the door will close?
Why does the door close only when I hold the button?
Could the remote be the problem?
When is it more than a sensor problem?
Sources
Last updated: